Fanuc HRTL Alarm Codes

Home > Fanuc > Alarm Codes > HRTL Alarm Codes

Fanuc HRTL Alarm Codes

HRTL-001 WARN Not owner
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-002 WARN File/Comm Tag does not exist
Cause: Either the file or the Comm Tag could not be found
Remedy: Either retype the file name or DEFINE the Comm Tag. Please refer to the section of
Defining and Starting FTP on a Device in the manual of Ethernet Controller Backup and RestoreFTP Setup and Operations.
________________________________________________________________
HRTL-003 WARN No such process
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-004 WARN Interrupted system call
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-005 WARN I/O error
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-006 WARN No protocol or device dest
Cause: The Comm Tag either does not have a protocol defined or if required does not have a port
assigned
Remedy: DEFINE a protocol to the Comm Tag or assign a port
________________________________________________________________
HRTL-007 WARN Arg list too long
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-008 WARN Exec format error
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-009 WARN Bad file number
Cause: The file number passed does not match with any open files.
Remedy: Copy the conditions which caused this to occur.
________________________________________________________________
HRTL-010 WARN No children
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-011 WARN No more processes
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-012 WARN Not enough core
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-013 WARN Access permission denied
Cause: Access Ethernet socket table permission denied.
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-014 WARN Invalid Comm Tag
Cause: A bad address has been detected
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-015 WARN Port device required
Cause: The selected protocol requires a device port
Remedy: First ensure the Port has No Use from Port Init Setup. Then assign it to the selected
Comm Tag
________________________________________________________________
HRTL-016 WARN Comm Tag already defined
Cause: Either the Comm Tag is STARTED or it’s presently in use
Remedy: Either STOP the Comm Tag or select another Tag. Please refer to the section of Defining
and Starting FTP on a Device in the manual of Ethernet Controller Backup and Restore- FTP Setup
and Operations.
________________________________________________________________
HRTL-017 WARN File exists
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-018 WARN Cross-device link
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-019 WARN Invalid device type
Cause: The passed Device Type is not a Comm Tag type (Cx or Sx)
Remedy: Only Comm Tags can be used with this command.
________________________________________________________________
HRTL-020 WARN Not a directory
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-021 WARN Is a directory
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-022 WARN Invalid argument
Cause: System does not support selected protocol.
Remedy: Either select another protocol or install the selected protocol.
________________________________________________________________
HRTL-023 WARN File table overflow
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-024 WARN Too many open files
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-025 WARN Not a typewriter
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-026 WARN Text file busy
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-027 WARN File too large
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-028 WARN No space left on device
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-029 WARN Illegal seek
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-030 WARN Read-only file system
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-031 WARN Too many links
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-032 WARN Broken pipe
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-035 WARN Operation would block
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-036 WARN Operation now in progress
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-037 WARN Operation now in progress
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-038 WARN Socket operation on non-socket
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-039 WARN Destination address required
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-040 WARN Message size too long
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-041 WARN Protocol wrong type
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-042 WARN Protocol not available
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-043 WARN Protocol not supported
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-044 WARN Socket type not supported
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-045 WARN Operation not supported
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-047 WARN Address family not supported
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-048 WARN Address already in use
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-049 WARN Can’t assign requested address
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-050 WARN Network is down
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-051 WARN Network is unreachable
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-052 WARN Connection dropped on reset
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-053 WARN Software caused connect abort
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-054 WARN Connection reset by peer
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-055 WARN No buffer space available
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-056 WARN Socket is already connected
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-057 WARN Socket is not connected
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-058 WARN Can’t send, socket is shutdown
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-060 WARN Ethernet Connection timed out
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-061 WARN Ethernet Connection refused
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-063 WARN Protocol family not supported
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-064 WARN Host is down
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-065 WARN Host is unreachable
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-066 WARN No urgent data
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-067 WARN No out of bound data
Cause: An error occurred in the Ethernet networking software (TCP/IP).
Remedy: Consult your network administrator or call the FANUC Robotics Service Hotline for
assistance.
________________________________________________________________
HRTL-068 WARN Device is already attached
Cause: Device is already in use
Remedy: Free Device for use
________________________________________________________________
HRTL-069 WARN Device Function Code invalid
Cause: Device does not support command
Remedy: Check useage against device
________________________________________________________________
HRTL-070 WARN Cannot detach with open files
Cause: Device in use
Remedy: Wait for command complete then retry
________________________________________________________________
HRTL-071 WARN Device is already allocated
Cause: Device is already allocated
Remedy: Wait until Device free then retry
________________________________________________________________
HRTL-072 WARN Device doesn’t support attach
Cause: Device does not support attaching
Remedy: Check useage against device
________________________________________________________________
HRTL-073 WARN End of device list reached
Cause: Device limit reached
Remedy: Check that device is valid
________________________________________________________________
HRTL-074 WARN Device is not supported
Cause: Device not available
Remedy: Check device installation