ABB Alarm Codes 10000 – 12000
10002, Program pointer has been reset
Description
The program pointer of task arg has been reset.
Consequences
When started, program execution will start on the first instruction of
the task’s entry routine. NOTE that the manipulator may move to
unexpected position when restarted!
Probable causes
The operator has probably requested this action manually.
10009, Work memory full
Description
The task arg has no memory left for new RAPID instructions or data.
Recommended actions
Save the program and then restart the system.
10010, Motors OFF state
Description
The system is in the Motors OFF state. It enters this state either after
switching from Manual mode to Automatic, or after the Motors ON
circuit has been opened during program execution.
Consequences
No operation will be possible until after closing the Motors ON circuit.
The manipulator’s axes are meanwhile held in position by mechanical
holding brakes.
10011, Motors ON state
Description
The system is in the Motors ON state.
Consequences
The Motors ON circuit has been closed., enabling power supply to the
manipulator’s motors. Normal operation may be resumed.
10012, Safety guard stop state
Description
The system is in the Guard stop state. It enters this state either after
switching from Automatic mode to Manual, or after the Motors ON
circuit has been opened by an Emergency Stop, General Stop,
Automatic Stop or Superior Stop.
Consequences
No operation will be possible until after closing the Motors ON circuit.
The manipulator’s axes are meanwhile held in position by mechanical
holding brakes.
Probable causes
Any safety device connected to the system’s stop inputs have been
opened. These are shown in the Circuit Diagram.
Recommended actions
1. Check which safety device caused the stop.
2. Close the device.
3. To resume operation, switch the system back to state Motors ON.
10013, Emergency stop state
Description
The system is in the Emergency stop state, since the Motors ON circuit
has been opened by an Emergency Stop device.
Consequences
All program execution and thus robot actions are immediately halted.
The robot axes are meanwhile held in position by mechanical holding
brakes.
Probable causes
Any emergency stop device connected to the emergency stop input
have been opened. These may be internal (on the controller or on the
teach pendant) or external (devices connected by the system builder).
The internal devices are shown in the Circuit Diagram.
Recommended actions
1) Check which emergency stop device caused the stop.
2) Close/reset the device.
3) To resume operation, switch the system back to state Motors ON by
pressing this button on the Control Module.
10014, System failure state
Description
Execution of all NORMAL tasks has been stopped due to malfunction.
Consequences
No start of program execution or manual manipulator jogging will be
possible until after the system has been restarted.
Probable causes
A large number of malfunctions may cause this condition. Please use
the teach pendant or RobotStudio to check other event log messages
for events occurring at this time!
Recommended actions
1. Determine what caused the stop by studying the event log.
2. Remedy the fault.
3. Restart the system as detailed in the Operator’s Manual.
10015, Manual mode selected
Description
The system is in the Manual mode.
Consequences
Programmed operation is possible, but only with a max. speed of 250
mm/s. The manipulator may also be jogged manually after pressing the
enabling device on the teach pendant.
10016, Automatic mode requested
Description
The system has been ordered to go to the Automatic mode.
Consequences
The system will go to the Automatic mode after confirmed from teach
pendant.
10017, Automatic mode confirmed
Description
The system is in the Automatic mode.
Consequences
The enabling device is disconnected. The robot can move without
human intervention.
10018, Manual mode full speed requested
Description
The system has been ordered to go to the Manual mode without any
speed restraints.
Consequences
The system will go to the Manual mode full speed.
10019, Manual mode full speed confirmed
Description
The system is in the Manual mode without any speed restraints.
Consequences
Programmed operation is possible while pressing the hold-to-run
button on the teach pendant. The manipulator may also be jogged
manually after pressing the enabling device on the teach pendant.
10020, Execution error state
Description
The program execution in task arg has been stopped due to a
spontaneous error.
Consequences
No program execution will be possible until the error has been
removed.
Probable causes
A large number of malfunctions may cause this condition. Please use
the teach pendant or RobotStudio to check other event log messages
for events occurring at this time!
Recommended actions
1. Determine what caused the stop by studying the event log.
2. Remedy the fault.
3. If neccesary, move Program Pointer to main before pressing start
button.
10021, Execution error reset
Description
The program execution in task arg has left a spontaneous error state.
10024, Collision triggered
Description
Some mechanical part of the manipulator has collided with a piece of
fixed equipment in the cell.
Consequences
Manipulator movement is interrupted and program execution is
stopped.
10025, Collision confirmed
Description
The collision detection has been confirmed.
Recommended actions
10026, Collision retraction
Description
The manipulator has attempted to back away from the obstacle, into
which it collided, and succeeded.
Consequences
The system is ready to go back to normal operation.
10027, Collision retraction fail
Description
The manipulator has attempted to back away from the obstacle, into
which it collided, and failed.
Consequences
The system is NOT ready to go back to normal operation.
Probable causes
This may be caused by the robot being stuck to the object into which it
collided.
Recommended actions
1) Go to Manual Mode.
2) Manually run the robot away from the object.
3) Resume operation by restarting the program.
10030, All axes commutated
Description
After checking, the system has found all manipulator axes to be
commutated.
Consequences
Normal operation is possible.
10031, All axes calibrated
Description
After checking, the system has found all manipulator axes to be
calibrated.
Consequences
Normal operation is possible.
10032, All revolution counters updated
Description
After checking, the system has found all revolution counters for all
manipulator axes to be updated.
Consequences
Normal operation is possible.
10033, All axes synchronized
Description
After checking, the system has found all manipulator axes to be
synchronized.
Consequences
Normal operation is possible.
10034, Axis not commutated
Description
After checking, the system has found that one or more manipulator
axes are not commutated.
Consequences
To enable operation, all manipulator axes must be commutated.
Probable causes
The manipulator drive motor and related units may have been altered,
e.g. after replacing a faulty unit.
Recommended actions
Commutate the manipulator axes as detailed in the manipulator
Product Manual.
10035, Axis not calibrated
Description
After checking, the system has found that one or more manipulator
axes are not calibrated.
Consequences
To enable operation, all manipulator axes must be calibrated.
Probable causes
The manipulator drive motor and related units may have been altered,
e.g. after replacing a faulty unit.
Recommended actions
Calibrate the manipulator axes as detailed in the manipulator Product
Manual.
10036, Revolution counter not updated
Description
After checking, the system has found that the revolution counters of
one or more manipulator axes are not updated.
Consequences
To enable operation, the revolution counters of all manipulator axes
must be updated.
Probable causes
The manipulator drive motor and related units may have been altered,
e.g. after replacing a faulty unit.
Recommended actions
Update the revolution counters of all manipulator axes as detailed in
the manipulator Product Manual.
10037, Axis not synchronized
Description
After checking, the system has found that one or more manipulator
axes are not synchronized.
Consequences
To enable operation, all manipulator axes must be synchronized.
Probable causes
The manipulator drive motor and related units may have been altered,
e.g. after replacing a faulty unit.
Recommended actions
Synchronize the manipulator axes as detailed in the manipulator
Product Manual.
10038, SMB memory is OK
Description
During startup, the system has found that all data on the Serial
Measurement Board (SMB) is OK.
Consequences
Operation is possible.
10039, SMB memory is not OK
Description
During startup, the system has found that data in the Serial
Measurement Board (SMB) memory is not OK.
Consequences
All data must be OK before automatic operation is possible. Manually
jogging the robot is possible.
Probable causes
There are differences between the data stored on the SMB and the data
stored in the controller. This may be due to replacement of SMB,
controller or both.
Recommended actions
1) Update the Serial Measurement Board data as detailed in Operator’s
Manual, IRC5.
10040, Program loaded
Description
A program or program module has been loaded into task arg. After
loading, arg bytes memory remain. The size of the loaded program is
arg.
10041, Program deleted
Description
A program or program module was deleted from task arg.
Consequences
If the deleted program contained the task entry routine, the program
will no longer be executable.
Probable causes
The program may have been removed manually.
Recommended actions
1) Define an entry routine in one of the task’s remaining programs, or:
2) Load a program containing an entry routine.
10042, Axis recalibrated
Description
Fine calibration or rev counter update was made for an axis in an
already synchronized mechanical unit.
10043, Restart failed
Description
The task arg can’t restart.
10044, Program Pointer updated
Description
The task arg could have changed the Program Pointer position.
Recommended actions
10045, System restarted
Description
An already installed system was restarted.
Recommended actions
10046, System restarted in cold mode
Description
First start after installation.
Recommended actions
10048, Background task did stop
Description
The task arg stopped without reason.
Recommended actions
10051, Event routine error
Description
The task arg could not start the specified system event routine arg. The
routine is either unknown to the system or the program is unlinkable.
Recommended actions
Insert the routine in a system module or correct the program.
10052, Regain start
Description
A regain movement has started.
Recommended actions
10053, Regain ready
Description
The regain movement is ready.
Recommended actions
10054, Regain rejected
Description
Regain on path not possible, as one client has already ordered it.
Recommended actions
A new regain movement is ordered during an already started regain
movement. Reduce the number of start orders from e.g system I/O
10055, Path process restarted
Description
The path process has been restarted.
Recommended actions
10060, Test of enable chain
Description
The enable chain is always tested at startup. If the test failed an error
message concerning enable will follow.
Recommended actions
If enable chain test at startup failed the related error message will be
“Enable chain timeout”
10061, A target has been modified
Description
A target in module arg in task arg has been modified or tuned.
Start line arg, column arg, end line arg.
10062, A module has been edited.
Description
Module arg in task arg has been edited between lines: arg, arg.
10063, Module has been edited
Description
Module arg in task arg has been edited.
10064, A module has been erased.
Description
Module arg in task arg has been erased.
10065, New user has started to modify RAPID.
Description
User arg has started with RAPID program modifications in task arg.
10066, Not possible to load system module
Description
System module arg in task arg cannot be loaded since the file is not
found.
10067, Program Pointer Reset
Description
Unable to reset the program pointer for task arg.
Consequences
The program will not start.
Probable causes
– No program is loaded.
– The main routine is missing.
– There are errors in the program.
Recommended actions
1. Load program if no program is loaded.
2. Check that the program has a main routine. If there is no main
routine, add one.
3. Check for errors in the program and correct them.
4. See previous error messages in the Event log.
10068, Start Program
Description
Unable to start program for task arg.
Consequences
The program will not execute.
10074, NFS server up
Description
The control system communicates correctly with the NFS server arg.
10075, NFS server down
Description
The control system is not able to communicate correctly with the NFS
server arg.
Consequences
If the server arg is defined as TRUSTED, robot program execution will
be stopped. If the server is defined as NON-TRUSTED, execution will
proceed. These definitions are specified in the Application manual –
Robot communication and I/O control.
Probable causes
If this message is displayed at first start-up, the server configuration
may be incorrect. If displayed during operation, the previously
working communication has been lost due to a broken connection.
Also see the I/O event log!
Recommended actions
1. Check the NFS server configuration.
2. Check all communication hardware, cables and such.
3. Check NFS client configuration on the controller.
10076, FTP server up
Description
The control system communicates correctly with the FTP server arg.
10077, FTP server down
Description
The control system is not able to communicate correctly with the FTP
server arg.
Consequences
If the server arg is defined as TRUSTED, robot program execution will
be stopped. If the server is defined as NON-TRUSTED, execution will
proceed. These definitions are specified in the Application manual –
Robot communication and I/O control.
Probable causes
If this message is displayed at first start-up, the server configuration
may be incorrect. If displayed during operation, the previously
working communication has been lost due to a broken connection.
Also see the I/O event log!
Recommended actions
1. Check the FTP server configuration.
2. Check all communication hardware, cables and such.
3. Check the FTP client configuration on the controller.
10080, An updated RAPID file is found
Description
The SEMISTATIC task arg has an older version of a module installed
than the source arg
Recommended actions
Restart the system with a P-START to install the newer version.
10081, Background task arg
Description
failed to load a newer version of a module. The source of the module
is arg.
Recommended actions
See previous messages for the cause or restart the system with a PSTART to load the newer version.
10082, RAPID Task supervision
Description
Task arg is not running. The system will be set in SysFail state. It’s now
impossible to change to motors on arg.
Recommended actions
See previous messages for the cause. Restart the system to reset the
error state.
10083, RAPID Task supervision
Description
Task arg is not running. The system will be set in motors off state. arg
Recommended actions
See previous messages for the cause.
10084, RAPID Task supervision
Description
Task arg is not running. All NORMAL tasks will also be stopped.
Recommended actions
See previous messages for the cause.
10085, RAPID Task supervision
Description
Task arg can’t be stopped. The trustLevel is set to a safety level.
Recommended actions
If the task should be possible to stop change the trustLevel or task type
in the system parameters menu.
10086, Robot is purged OK
Description
Purging pressure regained after a purge fault.
Recommended actions
10087, Purge state: arg.
Description
State changed.
Recommended actions
10090, P-Start done
Description
A P-Start is done.
Consequences
After restart the system’s state will be resumed except for manually
loaded programs and modules. Static and semistatic tasks are restarted
from the beginning, not from the state they had when the system was
stopped.
Modules will be installed and loaded in accordance with the set
configuration. System parameters will not be affected.
Probable causes
1. The P-start was ordered by the user.
2. The system forced the P-start due to inconsistent data, malfunction
or unrecoverable task state.
10091, Restart not possible
Description
A restart after collision detection is not possible before acknowledge
the error dialogue.
Recommended actions
10092, (Re)start not possible
Description
(Re)start is not possible due to lost contact with IO module arg
configured with trustlevel 3.
Recommended actions
10093, (Re)start not possible
Description
(Re)start of task arg is not possible before a warm start is done.
Recommended actions
The background task is configured with Trustlevel set to SysHalt
10095, At least one task is unchecked in the
task selection panel
Description
One or more of the NORMAL tasks are unchecked in the task selection
panel when performing a (re)start.
Recommended actions
10096, arg not active!
Description
The workobject arg contains a coordinated mechanical unit which is
not activated.
Recommended actions
Activate the mechanical unit and perform the operation again.
10097, Restart not possible
Description
The task arg is set in blocked state and the program is for that reason
not possible to restart from the current program position.
Recommended actions
The Program Pointer must be moved before restart.
10098, Restart not possible
Description
The task arg has been in system failure state and the program is for that
reason not possible to restart from the current program position.
Recommended actions
The Program Pointer must be moved before restart.
10099, Program start rejected
Description
The system has performed a soft stop, and the program may not be
restarted.
Consequences
The system goes to the Motors OFF state and can not be started. The
full meaning of this status is described in the Trouble shooting manual,
IRC5.
Probable causes
The soft stop may be caused by opening the safety circuit.
Recommended actions
1) Check the safety circuits for an open switch.
2) Go to Motors ON and restart the program.
10106, Service Message
Description
It’s time for service for robot arg because it is arg days since the last
service.
Recommended actions
10107, Service Message
Description
It remains arg days for robot arg until it’s time for service.
Recommended actions
10108, Service Message
Description
It’s time for service for robot arg cause it’s arg hours of production
since last service.
Recommended actions
10109, Service Message
Description
It remains arg hours of production for robot arg to next service.
Recommended actions
10110, Service Message
Description
The gearbox at arg of robot arg needs service.
Recommended actions
10111, Service Message
Description
The gearbox at arg of robot arg has reached arg of its service interval.
Recommended actions
10112, Service Message
Description
The system date and time has changed.
This could cause problems with the SIS calender notification.
Recommended actions
The SIS parameters Calender Limit and Calender Warning might need
to be changed
10120, Program stopped
Description
The task arg has stopped. The reason is that an external or internal stop
after current instruction has occurred.
Recommended actions
10121, Program stopped
Description
The task arg has stopped. The reason is that the task has reached an exit
instruction.
Recommended actions
10122, Program stopped
Description
The task arg has stopped. The reason is that the task is ready.
Recommended actions
10123, Program stopped
Description
The task arg has stopped. The reason is that the task is ready with this
step.
Recommended actions
10124, Program stopped
Description
The task arg has stopped. The reason is that the task has reached a
break instruction.
Recommended actions
10125, Program stopped
Description
The task arg has stopped. The reason is that an external or internal stop
has occurred.
Recommended actions
10126, Program stopped
Description
The task arg has stopped. The reason is that an error has occurred.
Recommended actions
10127, Backward execution not possible
Description
The task arg has stopped. The reason is that it is not possible to execute
backward past beginning of instruction list.
Recommended actions
10128, Backward execution not possible
Description
The task arg has stopped. The reason is that it is not possible to execute
backward past the instruction.
Recommended actions
10129, Program stopped
Description
The task arg has stopped. The reason is that the event routine for
RESET or POWER_ON is ready.
Recommended actions
10130, Program stopped
Description
The task arg has stopped. The reason is that the task is ready with this
move step.
Recommended actions
10131, Program stopped
Description
The task arg has stopped. The reason is that the routine called from
system IO interrupt is ready.
Recommended actions
10132, Program stopped
Description
The task arg has stopped. The reason could not be determined.
Recommended actions
10133, Program stopped
Description
The task arg has stopped. The reason is that the task is ready with the
execution of the UNDO handlers.
10150, Program started
Description
Execution of task arg has been started from the first instruction of the
task’s entry routine. The originator could not be determined.
Recommended actions
10151, Program started
Description
Execution of task arg has been started from the first instruction of the
task’s entry routine. The originator is an external client.
Recommended actions
10152, Program started
Description
Execution of task arg has been started from the first instruction of the
task’s entry routine. The start order was initiated by an action causing
the UNDO handler to execute.
10155, Program restarted
Description
Execution of task arg has been restarted from where it was previously
stopped. The originator could not be determined.
Recommended actions
10156, Program restarted
Description
Execution of task arg has been restarted from where it was previously
stopped. The originator is an external client.
Recommended actions
10157, Program restarted
Description
Execution of task arg has been restarted from where it was previously
stopped. The restart order was initiated by an action causing the
UNDO handler to execute.
10170, Background task arg
Description
refuse to start. Task is empty.
Recommended actions
10171, Background task arg
Description
refuse to start. Wrong state.
Recommended actions
10172, Background task arg
Description
refuse to start. Can’t set PP to the main routine.
Probable causes
The module that contains the main routine was not loaded since the
module file is missing in the target directory.
The module that contains the main routine was not loaded since the
configuration file has no entry for automatic loading of the module.
The main routine is missing.
The main entry is corrupted.
Recommended actions
Load the module by hand or perform an I-start when the cause of the
problem is removed.
10173, Background task arg
Description
refuse to start. Can’t set the execution mode.
Recommended actions
10174, Background task arg
Description
refuse to start. The start order failed.
Recommended actions
10175, Background task arg
Description
refuse to start due to a syntax error.
Recommended actions
10176, Background task arg
Description
refuse to start. Can’t load module.
Probable causes
The module file is missing in the target directory.
Recommended actions
1. Copy the module file to the target directory.
2. Perform an I-start.
10177, Task refuses to start
Description
Task arg:
There is not sufficient program memory or the program memory is
fragmented. Modules could be missing or data may not have been
installed.
Recommended actions
1. Unload/reload modules and warmstart.
2. Split large data structures.
3. P-start the system.
4. Increase stack size for task.
10178, A static/semistatic task can’t be stepped
Description
Task arg can’t be started.
A static/semistatic task can only run in continuous mode.
Consequences
No tasks will be started.
Probable causes
Trying to step (forward or backward) a static/semistatic task.
Recommended actions
Start arg in continuous mode.
10185, Task could not be prepared for start
Description
Task arg:
There is not sufficient program memory or the program memory is
fragmented. Modules could be missing or data may not have been
installed.
Recommended actions
1. Unload/reload modules and warm start.
2. Split large data structures.
3. P-start the system.
10190, Protected area not done
Description
A power fail did occur in the middle of a protected area for the task arg.
The system is trying to selfheal.
Recommended actions
10191, Protected area not done
Description
A power fail did occur in the middle of a protected area for the task arg.
A pending error is removed from the queue.
Recommended actions
10192, Protected area not done
Description
A power fail did occur in the middle of a protected area for the task arg.
A pending exit is removed from the queue.
Recommended actions
10193, Protected area not done
Description
A power fail did occur in the middle of a protected area for the task arg.
This may result in an extra program cycle.
Recommended actions
10194, Protected area not done
Description
A power fail did occur in the middle of a protected area for the task arg.
The task will be restarted from the main routine.
Recommended actions
10195, Protected area not done
Description
A power fail did occur in the middle of a protected area for the task arg.
All tasks are reset and all user programs are lost.
Recommended actions
Try to save the user program and do a warm start of the system
10196, Protected area not done
Description
A power fail did occur in the middle of a protected area for the task arg.
Recommended actions
10210, Execution cancelled
Description
The restart will clear the execution in task arg of a POWER ON system
event routine.
Recommended actions
10211, Execution cancelled
Description
The restart will clear the execution in task arg of a STOP system event
routine.
Recommended actions
10212, Execution cancelled
Description
The restart will clear the execution in task arg of an EMERGENCY
STOP system event routine.
Recommended actions
10213, Execution cancelled
Description
The restart will clear the execution in task arg of a START system
event routine.
Recommended actions
10214, Execution cancelled
Description
The restart will clear the execution in task arg of a RESTART system
event routine.
Recommended actions
10215, Execution cancelled
Description
The restart will clear the execution in task arg of a RESET system
event routine.
Recommended actions
10216, Execution cancelled
Description
The restart will clear the execution in task arg of an INTERNAL
system event routine.
Recommended actions
10217, Execution cancelled
Description
The restart will clear the execution in task arg of a USER routine.
Recommended actions
10218, Execution cancelled
Description
The restart will clear the execution in task arg.
Recommended actions
10219, Execution cancelled
Description
The restart will clear the execution in task argof a STEP system event
routine.
Recommended actions
10230, Backup step ready
Description
The backup step Prepare is ready.
Recommended actions
10231, Backup step ready
Description
The backup step Configuration is ready.
Recommended actions
10232, Backup step ready
Description
The backup of Task is ready.
Recommended actions
10250, Restore step ready
Description
The restore step Prepare is ready.
Recommended actions
10251, Restore step ready
Description
The restore step Configuration is ready.
Recommended actions
10252, Restore step ready
Description
The restore of Task is ready.
Recommended actions
10253, Restore step ready
Description
The restore of User Task is ready.
Recommended actions
10260, System diagnostics info generated
Description
System diagnostics information was successfully generated to file arg
10261, System diagnostics info unavailable
Description
User requested to save diagnostics system information to file arg.
System was unable to fulfill this request.
Consequences
Diagnostics system information is normally used when reporting a
problem with the system to ABB support.
Probable causes
The system is in such state that it is not possible to generate the
requested information.
Please check that the device has enough space left.
Recommended actions
If you are experiencing a problem with the system contact ABB
support.
10270, Cyclic Brake Check Done
Description
The Cyclic Brake Check has been done for all brakes supervised by
Safety Controllers.
10300, A P-Start is ordered
Description
The P-Start has been ordered from the system.
Recommended actions
10301, A P-Start is ordered
Description
The P-Start has been ordered manually or automatically during a
configuration.
Recommended actions
10304, An update has been ordered
Description
An update of program configuration is done.
Recommended actions
10350, Update of task failed
Description
The system could not update task arg to the new configuration.
Recommended actions
10351, A task is removed
Description
The task arg was removed because of configuration changes.
Recommended actions
10352, A task is added
Description
The task arg was installed because of configuration changes.
Recommended actions
10353, A task is reinstalled
Description
The task arg was reinstalled because of configuration changes.
Recommended actions
10354, Restore aborted due to lost system data.
Description
The system is using a backup of the system data, since the system data
was not properly saved at last shutdown. Due to this, a previously
ordered Restore from directory arg was attempted again, but was
aborted.
Consequences
No RAPID programs or modules will be loaded.
Probable causes
The system data was not properly saved at last shutdown.
Recommended actions
After recovering from the system data loss by a (B)ackup-Restart or
system re-installation, please verify that the backup directory arg is
OK, and perform the Restore again.
10355, Restore error
Description
Error during the restore of Task. Trying to load to unknown task, arg.
Consequences
Loading has been aborted for arg.
Probable causes
The current system doesn’t have the same options as the one used to
create the backup.
10400, User arg logged on
Description
User arg logged on using arg.
10401, User arg logged off
Description
User arg using arg logged off.
10420, New unsafe robot path
Description
The robot path has been cleared after a target has been modified in task
arg. The robot will for that reason move towards the position pointed
out by the move instruction at the program pointer. Move instructions
between the modified target and the program pointer will be skipped.
Consequences
The programmed speed is used for this movement.
The new untested path may contain obstacles that might cause a
collision.
Recommended actions
Check your program pointer and move it if necessary.
Reduce the speed.
10421, Planned path not aborted
Description
A target that may be part of the planned robot path has been modified.
The new target position will be used the next time the instruction with
the target is executed.
Consequences
The current planned path is using the old target position.
Recommended actions
If the current planned path is unsafe, move the program pointer to abort
it.
11020, Backup error
Description
Error during the backup step Prepare. Unknown error.
Recommended actions
arg
11021, Backup error
Description
Error during the backup step Prepare. General error.
Recommended actions
arg
11022, Backup error
Description
Error during the backup step Prepare. The directory contains items that
are to be created.
Recommended actions
arg
11023, Backup error
Description
Error during the backup step Prepare. The directory lacks at least one
neccessary item.
Recommended actions
arg
11024, Backup error
Description
Error during the backup step Prepare. The directory does not exist.
Recommended actions
arg
11025, Backup error
Description
Error during the backup step Prepare. Directory cannot be created.
Recommended actions
arg
11026, Backup error
Description
Error during the backup step Prepare. Error whilst writing the backup.
Recommended actions
arg
11027, Backup error
Description
Error during the backup step Prepare. Error reading configuration
parameters.
Recommended actions
arg
11028, Backup error
Description
Error during the backup step Prepare. Error writing configuration
parameters.
Recommended actions
arg
11029, Backup error
Description
Error during the backup step Prepare. The structure is too deep.
Recommended actions
arg
11030, Backup error
Description
Error during the backup step Prepare. No more objects.
Recommended actions
arg
11031, Backup error
Description
Error during the backup step Prepare. The directory lacks at least one
neccessary item.
Recommended actions
arg
11032, Backup error
Description
Error during the backup step Prepare. The system version doesn’t
match the backup.
Recommended actions
arg
11033, Backup error
Description
Error during the backup step Prepare. Error restoring configuration
parameters.
Recommended actions
arg
11034, Backup error
Description
Error during the backup step Prepare. Error restoring configuration
parameters.
Recommended actions
arg
11035, Backup error
Description
Error during the backup step Prepare. Mismatch between current
system and the backup.
Recommended actions
arg
11036, Backup error
Description
Error during the backup step Prepare. Write error.
Consequences
The backup will be incomplete.
Probable causes
You may not have write access to the backup drive.
The drive might be full.
If it is a network drive you might have lost connection.
Recommended actions
arg
11037, Backup error
Description
Error during the backup step Prepare. At least one modname is too
long.
Recommended actions
arg
11038, Backup error
Description
Error during the backup step Prepare. Unknown task.
Recommended actions
arg
11039, Backup error
Description
Error during the backup step Prepare. Storage media full.
Recommended actions
arg
11040, Backup error
Description
Error during the backup step Prepare. Item not possible to delete.
Recommended actions
arg
11120, Backup error
Description
Error during the backup step Configuration. Unknown error.
Recommended actions
11121, Backup error
Description
Error during the backup step Configuration. General error.
Recommended actions
11122, Backup error
Description
Error during the backup step Configuration. The directory contains
items that are to be created.
Recommended actions
11123, Backup error
Description
Error during the backup step Configuration. The directory lacks at
least one neccessary item.
Recommended actions
11124, Backup error
Description
Error during the backup step Configuration. The directory does not
exist.
Recommended actions
11125, Backup error
Description
Error during the backup step Configuration. Directory cannot be
created.
Recommended actions
11126, Backup error
Description
Error during the backup step Configuration. Error whilst writing the
backup.
Recommended actions
11127, Backup error
Description
Error during the backup step Configuration. Error reading
configuration parameters.
Recommended actions
11128, Backup error
Description
Error during the backup step Configuration. Error writing
configuration parameters.
Recommended actions
11129, Backup error
Description
Error during the backup step Configuration. The structure is too deep.
Recommended actions
11130, Backup error
Description
Error during the backup step Configuration. No more objects.
Recommended actions
11131, Backup error
Description
Error during the backup step Configuration. The directory lacks at
least one neccessary item.
Recommended actions.
11132, Backup error
Description
Error during the backup step Configuration. The system version
doesn’t match the backup.
Recommended actions
11133, Backup error
Description
Error during the backup step Configuration. Error restoring
configuration parameters.
Recommended actions
11134, Backup error
Description
Error during the backup step Configuration. Error restoring
configuration parameters.
Recommended actions
11135, Backup error
Description
Error during the backup step Configuration. Mismatch between
current system and the backup.
Recommended actions
11136, Backup error
Description
Error during the backup step Configuration. Write error.
Recommended actions
11137, Backup error
Description
Error during the backup step Configuration. At least one modname is
too long.
Recommended actions
11138, Backup error
Description
Error during the backup step Configuration. Unknown task.
Recommended actions
11139, Backup error
Description
Error during the backup step Configuration. Storage media full.
Recommended actions
11140, Backup error
Description
Error during the backup step Configuration. Item not possible to
delete.
Recommended actions
11220, Backup error
Description
Error during the backup of Task. Unknown error.
Recommended actions
11221, Backup error
Description
Error during the backup of Task. General error.
Recommended actions
11222, Backup error
Description
Error during the backup of Task. The directory contains items that are
to be created.
Recommended actions
11223, Backup error
Description
Error during the backup of Task. The directory lacks at least one
neccessary item.
Recommended actions
11224, Backup error
Description
Error during the backup of Task. The directory does not exist.
Recommended actions
11225, Backup error
Description
Error during the backup of Task. Directory cannot be created.
Recommended actions
11226, Backup error
Description
Error during the backup of Task. Error whilst writing the backup.
Recommended actions
11227, Backup error
Description
Error during the backup of Task. Error reading configuration
parameters.
Recommended actions
11228, Backup error
Description
Error during the backup of Task. Error writing configuration
parameters.
Recommended actions
11229, Backup error
Description
Error during the backup of Task. The structure is too deep.
Recommended actions
11230, Backup error
Description
Error during the backup of Task. No more objects.
Recommended actions
11231, Backup error
Description
Error during the backup of Task. The directory lacks at least one
neccessary item.
Recommended actions
11232, Backup error
Description
Error during the backup of Task. The system version doesn’t match the
backup.
Recommended actions
11233, Backup error
Description
Error during the backup of Task. Error restoring configuration
parameters.
Recommended actions
11234, Backup error
Description
Error during the backup of Task. Error restoring configuration
parameters.
Recommended actions
11235, Backup error
Description
Error during the backup of Task. Mismatch between current system
and the backup.
Recommended actions
11236, Backup error
Description
Error during the backup of Task. Write error.
Recommended actions
Check: No space left on device. Corrupt device.
11237, Backup error
Description
Error during the backup of Task. At least one modname is too long.
Recommended actions
11238, Backup error
Description
Error during the backup of Task. Unknown task.
Recommended actions
11239, Backup error
Description
Error during the backup of Task. Storage media full.
Recommended actions
11240, Backup error
Description
Error during the backup of Task. Item not possible to delete.
Recommended actions